i Manual Number: 121201 USERS GUIDE DXE-CAT-S2L HDMI HDBaseT CAT Extender with IP Control
7 User Guide General Settings Status - Shows the current IP Address, Hostname, Mac Address, Serial number, and the firmware revision. Change Pas
8 User Guide Network Settings Current Network Settings - Shows the current IP Address, Subnet Mask, Gateway, Hostname, and Mac Address. Network
9 User Guide Port Settings Master Remote IP – Enter the Aurora control system IP the DXE-LXC is going to push information to. Note: If an Aurora c
10 User Guide Port Processing Session – Choose between the following modes of operation. Manual - Ports are just serial ports manipulated via RP
11 User Guide Port Settings (Manual) With port processing session set to manual there will be no additional selections as the system is set to tri
12 User Guide Port Settings (Push to Variable) Remote Session IP Address – Enter the IP address the variable is to be sent to an Aurora control de
13 User Guide Port Settings (Telnet Server) Telnet Local Port Number – Defaulted to Port 23 but can be changed to other port numbers. Telnet Timeo
14 User Guide Port Settings (Telnet Client) Remote Session IP Address – Enter Telnet Server IP Address. Telnet Remote Port Number – Defaulted to P
15 User Guide Port Settings (Push to Port) Remote Session IP Address – Enter IP address of serial port on another Aurora control device to targ
16 User Guide Port Settings (Pass-Through) Pass-Through mode allows the serial ports on both the DXE-CAT-TX and DXE-CAT-RX to become a virtual ca
i User Guide SAFETY INSTRUCTIONS Please review the following safety precautions. If this is the first time using this model, then read this manual
17 User Guide IP Commands TCP/RPC Commands Remote procedure calls (RPCs) are used to control the DXE-CAT-S2L from any device with a web browser
18 User Guide TCP/RPC Command Usage Sample Usage Send the serial command “PowerOn<0D>” out the RX serial port: method=Serial_Send¶m1
19 User Guide Web Server The DXE-CAT-TX2L has a built in web server that can hold up to 8MB of web pages (including firmware). Using FTP, webpage
20 User Guide CONNECTOR PIN DEFINITION HDMI Pin 1 TMDS Data2+ Pin 8 TMDS Data0 Shield Pin 15 SCL Pin 2 TMDS Data2 Shield Pin 9 TMDS Data0–
21 User Guide APPENDIX 1 Troubleshooting Problem Solution 1. No Video Signal. a. Check that the power plug is properly inserted into a function
22 User Guide APPENDIX 3 Technical Specifications Model Name DXE-CAT Technical DXE-CAT-S2L Distance 330ft (1080p 60Hz / 4k2k 48bit color CAT 5e/6/
23 User Guide APPENDIX 4 Warranty Limited 3 Year Warranty Aurora Multimedia Corp. (“Manufacturer”) warrants that this product is free of defects
24 User Guide This product warranty extends to the original purchaser only and will be null and void upon any assignment or Aurora Multimedia Corp
ii User Guide TABLE OF CONTENTS PACKAGE CONTENTS ...
1 User Guide PACKAGE CONTENTS Please make sure the following items are included within your package. Contact your dealer if any items are missing o
2 User Guide INTRODUCTION About The DXE-CAT-S2L is part of the growing Digital Xtreme Series. This product is different than the typical CAT exten
3 User Guide Front & Rear Panel DXE-CAT-TX2L Front LED Indicators • IR Out – Blinks when emitting IR to device from IR Port. It is no
4 User Guide Front & Rear Panel DXE-CAT-RX2 Front LED Indicators • IR Out – Blinks when emitting IR to device from IR Port. It is norm
5 User Guide IR EXTENDERS IR Blaster IR Receiver IR Connections The DXE-CAT Series has the ability to a
6 User Guide IP Setup Default IP The default IP out of the box is 192.168.1.10 static. Make certain to change the IP on the unit at a time or you
Comments to this Manuals